{ "id": "flexible-drainage-rods-12-piece", "sku": "flexible-drainage-rods-12-piece", "title": "Flexible Drainage Rods 12 Piece Set", "slug": "flexible-drainage-rods-12-piece", "price": 43.99, "currency": "GBP", "availability": "in_stock", "category": "drain-cleaning-brushes", "category_label": "Drain Rods, Brushes & Jetter Hoses", "tags": [], "colors": [], "materials": [], "dimensions": null, "weight": "1.94 kg", "images": [ "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/main-flexible-drainage-rods-12-piece.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-2.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-3.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-4.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-5.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-6.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-7.jpg", "https://ezydrains.co.uk/dropship-images/drain-cleaning-brushes/flexible-drainage-rods-12-piece/flexible-drainage-rods-12-piece-8.jpg" ], "description_short": "Ten screw-together 920mm rods with brass end connections, a 100mm rubber plunger and a 70mm double worm screw, giving you up to 9.2 metres of reach for outside drains, gullies and chimney flues.", "description": "The problem with a slow outside drain\n\nIt starts quietly. The gully by the kitchen takes a few seconds longer to clear. Then it takes a minute. Then there is a shallow pool of grey water sitting there after every wash, with a smell that gets worse in warm weather. Eventually something inside the house gurgles, usually a downstairs sink or the toilet, and that is the drain telling you the blockage has backed up far enough to matter.\n\nAlmost every household drain blockage sits in the same few places. The gully trap, the bend just past it, the run between the gully and the inspection chamber, or the chamber itself. None of those are deep, complicated plumbing. They are accessible from the surface with the right tool, and the right tool is a set of drain rods.\n\nThe reason people call someone out instead is simply that they do not own rods. A bucket and a stick does not work. A garden hose pushes water at the blockage but has no way to break it up. Rods do both, because you can physically reach the blockage and attack it with a head designed for the job.\n\nWhat a 12 piece set actually gives you\n\nThis set has ten flexible rods at 920mm each, a 100mm rubber plunger and a 70mm double worm screw. Screw all ten rods together and you are working with roughly 9.2 metres of reach. On a normal house, that covers the distance from a gully to the nearest chamber with room to spare.\n\nThe rods are flexible rather than stiff. That sounds like a weakness and is actually the whole point. Drain runs are not straight. There is a trap under the gully, there are bends where the pipe turns to follow the wall, and there is usually a step down into the chamber. A rigid rod stops dead at the first of those. A flexible rod bends through, keeps contact with the pipe wall, and carries on.\n\nConnections are the other thing worth paying attention to. These rods use crimped and pinned rustproof connectors with brass plated ends. Pinning means the fitting is mechanically locked to the rod, not just glued or pressed on, so it does not pull free when you are twisting hard. Brass plating keeps the threads from seizing up after a season in a damp shed.\n\nHow rodding actually works\n\nLift the inspection chamber lid first. This one step tells you where the blockage is. A chamber full of standing water means the problem is downstream, between that chamber and the next one or the main sewer. An empty chamber with a flooded gully means the problem is upstream, in the short run from the gully.\n\nScrew two or three rods together to start. Fit the plunger head. Feed it into the pipe in the direction of the blockage and push. Keep every twist clockwise, always, because the joints tighten clockwise and loosen the other way. Add rods one at a time as you go deeper, and do each joint up properly before you commit it to the pipe.\n\nThe plunger works by sealing against the pipe wall and using the standing water as a ram. Short, firm push and pull strokes build pressure and release it, which breaks up soft material. Most grease, soap, paper and silt blockages give way to this within a few minutes.\n\nIf the plunger does not shift it, something fibrous is probably holding the mass together. Wet wipes are the usual suspect, followed by rags and fine root hair that has found a cracked joint. That is when you swap to the 70mm double worm screw. Corkscrew it clockwise into the blockage so it bites, then draw it back steadily. You are pulling the material out rather than pushing it along.\n\nWhen the water goes, flush the line properly. Run a hose into the gully for a few minutes and watch the chamber to confirm it is flowing clear. A partial clear that you walk away from will block again within weeks.\n\nWho this suits\n\nAnyone in an older property with open gullies and inspection chambers in the garden. Anyone on a long drive where the drain run between the house and the main sewer is measured in metres rather than feet. Landlords with more than one property, because the cost of a single call out usually covers the set several times over. Allotment holders, smallholders and anyone who looks after a yard with surface drainage.\n\nIt is also worth knowing that rods of this type are commonly used for chimney flues. If you burn wood and want to sweep your own flue, you would need a brush head sized to the flue, which is not included here, but the rods themselves do that job. The same goes for long ducts and awkward cavities where your arm does not reach.\n\nWhere a rod set is not the answer is inside the house. Narrow waste pipes under a sink want a small hand auger, not a 100mm plunger head. And if you have a collapsed pipe or long standing root damage, no rod will fix that. You want a professional with a camera to find out exactly what has happened underground.\n\nChoosing between sets\n\nLength is the first filter. Shorter sets of five or six rods sound cheaper until you discover your chamber is eight metres from the gully. Ten rods at 920mm covers most domestic layouts without you having to borrow more.\n\nJoint type is the second. Screw together fittings are the common standard and they work well as long as they are pinned to the rod properly. The failures you read about are nearly always loose joints or anticlockwise turning, not the fitting design itself.\n\nAttachment choice is third. A plunger and a worm screw between them handle the two main categories of blockage, soft and fibrous. Some people add a rubber disc or a scraper head later. Because the thread is the standard type, extra heads generally fit.\n\nFinally, think about weight and storage. This set comes in at 1.94 kg, which is nothing to carry and easy to hang on a garage wall. A set that lives somewhere accessible is a set you will actually use.\n\nLooking after them\n\nRinse everything with clean water the moment you finish. Scrub the attachment heads, pay attention to the threads, and let it all dry before it goes back in the shed. Grit in the fittings is what grinds threads over time, and standing water in the connectors is what ages them.\n\nStore the set dry and roughly straight. Keep gloves with it so you are not hunting for a pair next time. Before every job, run through the joints and check each one screws up tight and clean.\n\nThe short version\n\nA blocked outside drain is a job most people can do themselves, and the only reason they do not is a missing tool. Ten flexible 920mm rods give you around 9.2 metres of reach. The 100mm rubber plunger clears soft blockages by pressure. The 70mm double worm screw pulls out rags, wipes and root hair. Keep every twist clockwise, check your joints, and flush the line through when the water goes.\n\nBuy it once, hang it on the wall, and the next time the gully fills up you are outside with gloves on rather than on the phone waiting for a van.", "llm_summary": "The Crystals Flexible Drainage Rods 12 Piece Set is a manual drain clearing kit supplied by Denny International under model number 5116. It contains ten flexible rods, each 920mm long, giving roughly 9.2 metres of total reach when screwed together, plus a 100mm rubber plunger head and a 70mm double worm screw attachment. Rods use crimped and pinned rustproof connectors with brass plated end fittings and join by turning clockwise. The set is black, weighs 1.94 kg, and is listed with product dimensions of 92 x 10 x 92 cm. It is intended for clearing outside drains, gullies and inspection chambers, and is also used for chimney flues and hard to reach cavities. Material and country of origin are not specified by the maker.", "returnable": true, "return_policy": "14-day right to cancel from delivery under the Consumer Contracts Regulations 2013, buyer pays return postage; the refund may be reduced if the item has been used beyond normal handling; Consumer Rights Act 2015 rights for faulty goods. Return postage on faulty goods is ours.", "shipping_profile": "standard", "warranty": null, "brand": "EzyDrains Company", "gtin": null, "mpn": null, "condition": "new", "url": "https://ezydrains.co.uk/flexible-drainage-rods-12-piece/", "canonical_url": "https://ezydrains.co.uk/flexible-drainage-rods-12-piece/", "json_url": "https://ezydrains.co.uk/api/products/flexible-drainage-rods-12-piece.json", "updated_at": "2026-10-11" }