{ "id": "brass-basin-plug-with-hair-basket-34-to-38mm", "sku": "brass-basin-plug-with-hair-basket-34-to-38mm", "title": "Brass Basin Plug with Hair Basket (34-38mm)", "slug": "brass-basin-plug-with-hair-basket-34-to-38mm", "price": 24.99, "currency": "GBP", "availability": "in_stock", "category": "sink-and-bath-plugs", "category_label": "Sink & Bath Plugs", "tags": [], "colors": [], "materials": [], "dimensions": null, "weight": "100 g", "images": [ "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/main-brass-basin-plug-with-hair-basket-34-to-38mm.jpg", "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/brass-basin-plug-with-hair-basket-34-to-38mm-2.jpg", "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/brass-basin-plug-with-hair-basket-34-to-38mm-3.jpg", "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/brass-basin-plug-with-hair-basket-34-to-38mm-4.jpg", "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/brass-basin-plug-with-hair-basket-34-to-38mm-5.jpg", "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/brass-basin-plug-with-hair-basket-34-to-38mm-6.jpg", "https://ezydrains.co.uk/dropship-images/sink-and-bath-plugs/brass-basin-plug-with-hair-basket-34-to-38mm/brass-basin-plug-with-hair-basket-34-to-38mm-7.jpg" ], "description_short": "Made from brass with a built-in strainer basket that catches hair before it reaches the pipe, it presses down to seal and presses again to release, and it fits by hand into basin drain holes measuring 34 to 38mm.", "description": "The small part that causes the big annoyance\n\nA basin plug is one of those things nobody thinks about until it stops working. Then it becomes the most irritating object in the house. You run a few inches of water to rinse a razor, turn away for thirty seconds and come back to an empty bowl. Or the cap sticks halfway down and you end up pressing it three times before it decides to seal. Or worse, the water takes a minute to drain because a decade of hair has knitted itself into the pipe below.\n\nAll three problems come back to the same component. In a modern basin, the plug is not a rubber stopper on a chain. It is a spring-loaded core that sits inside the waste, and it is designed to be removable. Which means you can replace it without touching the pipework, calling anyone out, or lifting a single tool.\n\nThis brass basin plug with hair basket is that replacement part. It handles the sealing, it handles the draining, and it adds something the original probably did not have, which is a strainer that catches hair before it ever reaches the trap.\n\nHow a pop up basin plug actually works\n\nThe mechanism is simple once you have seen it. Inside the plug body there is a spring and a small cam. Press the cap down and the cam rotates to a locked position, holding the cap flush against the waste rim so water cannot escape. Press it again and the cam releases, the spring pushes the cap back up, and the gap underneath lets the basin empty.\n\nThat is the whole thing. There is no rod running down behind the tap, no lever to pull, and nothing to adjust once it is in. Older basins often used a linkage system where a lift rod behind the mixer connected to an arm under the basin. Those systems work, but they go out of alignment, the arm corrodes, and getting under a basin to fix one is nobody's idea of a good afternoon. A press-action core removes all of that.\n\nMaterial matters here more than you might expect. The cam and spring take a small impact every time someone presses the cap, several times a day, for years. A brass body keeps its shape under that load and sits with enough weight to seat squarely in the waste. Light plastic cores tend to flex, which is why they start leaking around the rim before the spring itself has worn out.\n\nThe hair basket is the real upgrade\n\nHere is the part worth paying attention to. Standard pop up cores have a gap around the cap and nothing behind it. Hair goes straight past, down into the U-bend, and starts collecting. Soap and toothpaste bind to it. Within a year or two you have a slow drain, and the only fix is unscrewing the trap over a bucket.\n\nA built-in strainer basket changes the sequence. Hair gathers inside the plug, above the waste, where you can lift it out with the plug itself. Tip it into the bin, rinse the basket under the tap, drop it back in. Fifteen seconds, once a week.\n\nIf you live in a household with long hair, this is the single most useful feature on the product. It is not glamorous. It just means you spend your Saturday doing something other than kneeling in a bathroom cupboard with a wrench.\n\nGetting the size right\n\nThis is the one thing to check before ordering. The plug suits drain holes with an inner diameter between 34mm and 38mm, which covers a lot of standard basin wastes but not all of them.\n\nTo measure, lift the old core out of the basin. Put a ruler or tape across the opening and read the distance across the inside of the metal waste, not across the outside of the rim you can see from above. Take the measurement at the narrowest point, since some wastes taper slightly as they go down. If the number sits anywhere from 34 to 38, you are good.\n\nIf your hole measures toward the upper end and the plug feels like it has a little play, that is what the included rubber ring is for. It slips around the body and builds out the diameter so the plug grips the sides properly. Fit the ring first, then push the plug home.\n\nIf your measurement is well outside the range, this is not the right part. Kitchen sinks and most baths use larger wastes, so measure rather than assume. A plug that nearly fits will never seal.\n\nFitting it, step by step\n\nStart by pulling the old core out. Most lift straight up with a firm grip. If limescale has it stuck, twist gently as you pull rather than yanking, and run hot water over the area first to soften deposits.\n\nWith the hole clear, wipe around the inside of the waste. Any grit, old sealant or hair left on the seating surface is the main cause of a plug that will not hold water, so this thirty seconds is worth doing properly.\n\nFit the rubber ring if you need it, then drop the new plug in and press it down until it seats. Run the tap, press the cap to seal, and watch the level for a minute. If it holds, you are finished. If it drops slowly, lift the plug, check for debris on the sealing face and refit.\n\nThat is the entire job. No tools, no sealant, no access required under the basin.\n\nWho this suits\n\nIt suits anyone whose basin has stopped holding water. It suits households with long hair who are tired of slow drains. It suits renters, because nothing is altered permanently and the original core can go back in when you move out. It suits anyone replacing a plug that has gone sticky, dull or simply vanished.\n\nIt is also a sensible thing to keep in a drawer if you have just moved into a place with an older bathroom. These parts fail eventually, and having the replacement already in the house is better than discovering the problem on a weekend.\n\nKeeping it working\n\nThe care routine is short. Wipe the cap with a soft damp cloth and dry it, which stops water marks forming on the brass. Lift the plug out regularly and empty the basket. Rinse it under running water.\n\nWhat to avoid is just as important. Bleach, caustic drain unblockers, scouring powder and abrasive pads can all mark the surface. Harsh chemicals are the fastest way to dull a brass finish, and most of the time they are not needed anyway, because the whole point of the strainer is that you are removing the hair by hand before it ever becomes a blockage.\n\nIf the press action starts feeling slow or gritty, do not force it and do not oil it. Lift the plug out, rinse away the soap film around the shaft, and refit. That fixes nearly every stiff mechanism.\n\nThe short version\n\nA basin plug is a cheap part doing a job you notice only when it fails. This one is brass rather than plastic, it presses to seal and presses to drain, and it carries a strainer basket that stops hair reaching your pipework. It fits drain holes measuring 34mm to 38mm inside, a rubber ring is included for the wider end of that range, and it goes in by hand in a couple of minutes.\n\nMeasure your drain hole, check it lands in range, and the rest is easy.", "llm_summary": "The Brass Basin Plug with Hair Basket is a replacement pop up basin waste core for bathroom sinks, branded Abnii, model Abnii-005, UPC 757842970441. It is made of brass and fits basin drain holes with an inner diameter of 34mm to 38mm, with a rubber ring included to adapt to the wider end of that range. A strainer basket inside the plug collects hair to help prevent drain blockages. The cap presses down to seal the basin and presses again to release and drain. Installation needs no tools, as the old bounce core is lifted out and the new one pushed in. Listed dimensions are 6.2cm wide by 5cm high, weight 100g, country of origin China. Colour and finish are not specified by the maker.", "returnable": true, "return_policy": "14-day right to cancel from delivery under the Consumer Contracts Regulations 2013, buyer pays return postage; the refund may be reduced if the item has been used beyond normal handling; Consumer Rights Act 2015 rights for faulty goods. Return postage on faulty goods is ours.", "shipping_profile": "standard", "warranty": null, "brand": "EzyDrains Company", "gtin": null, "mpn": null, "condition": "new", "url": "https://ezydrains.co.uk/brass-basin-plug-with-hair-basket-34-to-38mm/", "canonical_url": "https://ezydrains.co.uk/brass-basin-plug-with-hair-basket-34-to-38mm/", "json_url": "https://ezydrains.co.uk/api/products/brass-basin-plug-with-hair-basket-34-to-38mm.json", "updated_at": "2026-10-11" }